LAT5004AAW Replacing the Maytag Water Pump 202203
By · CommentsOK, I did it. I turned the machine on it’s side and loosed the water pump from the machine’s base by removing 3 5/16″ screws. After removing the two hoses attached with hose clamps, the pump slipped right out and the new one went in just as easily. I replaced the new belts that I ordered and the machine runs perfectly. And to think I was ready to go buy a new machine.
WCSR4170G1WW GE Top Load Washer Not Spinning
By · CommentsThe Reset works…….IT LIVES!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Spinning is working fine now, the LED is blinking 1 time per second and faster with the spin on. We ran it through a whole cycle and it works great again. Can’t thank you guys enough, you have saved us a ton of money!! Thank you, Thank you, have a great weekend guys!!
Thanks for everyone’s help. This is an awesome service and got me looking in the right direction. It was the vent for sure, ran it twice all the way through and not one drop of water! I guess in 17 years of running perfect I should do some maintenance.
via Whirlpool dishwasher runs great, but door leaks like crazy.
wm2277hs help with washer
By · CommentsHere’s what the manual has to say regarding the LE code:
The connector (3-pin, male, white) in the MOTOR
HARNESS is not connected to the connector
(3-pin, female, white) of STATOR ASSEMBLY.
• The electric contact between the connectors
(3-pin, male, white) in the MOTOR HARNESS
and 4-pin, female, white connector in the MAIN PWB
ASSEMBLY is bad or unstable.
• The MOTOR HARNESS between the STATOR
ASSEMBLY and MAIN PWB ASSEMBLY is cut (open
circuited).
• The hall sensor is out of order/defective
If you have OHmed out the wire harness from the main PCB to the motor, and have checked the stator on the motor for signs of broken or loose wiring, then you can assume the PCB is bad.
via help with washer.
Frigidaire chest freezer
By · CommentsI would like to thank the people who helped me with my GE SS fridge problem. It turned out to be the compressor. I replaced the compressor and it has been working fine since.
WM2277HW LG Washer leak
By · CommentsWhat I do to remove gasket.
1) Use a pick or small screwdriver put in the spring at the bottom pry it out of the gasket. Spring and wire clamp will come out.
2) pull rubber gasket off the front of the washer.. fold it inside out into the tub.
3) Use a pick or small screwdriver put in the spring at the bottom pry it out of the gasket. Spring and wire clamp will come out inside of gasket.
4) pull rubber gasket off the outer tub.
To install the new gasket.
1) heat the gasket in a dryer
2) Start at the top. Take the top of the gasket insert it into the lip of the outer tub. work your way around the outer tub until you get it in all the way around..
(if your fingers are too big you may have to remove the front bricks)
3)fold the gasket into the tub inside out.
4)take the wire with spring start at the top ( use the shark clamp to open the spring) slide the wire and spring around gasket and outer tub. release shark clamp
5)Pull gasket out of tub. insert fill hose or spray hose or light if you have them.
6) start at the top insert the gasket to washer front lip. work your way around the front.
7)take the wire with spring start at the top (use the shark clamp to open the spring) slide the wire and spring around gasket and outer tub. release shark clamp
via LG Washer leak.
FWX223LBS0 Top Load Washer Drain Issue
By · CommentsRemove the front panel and also the hose going into the small electric pump you’ll find right in front. If something is blocking the flow, it’s likely there. Other than that, the outlet from the tub may be gunked up. In this case, fill the washer on the lowest level with very hot water, add a cup of powdered dishwasher detergent and let it circulate a few minutes, then set the timer to drain.
tip: Never use drain cleaner in a washer..it will ruin the seals.
DLG2526W LG Dryer Rattle/Vibration
By · CommentsLG had a different repair company sent to check the dryer. Turns out the bracket holding the motor was vibrating against the bottom of the dryer. The tech wedged some foam between and it took care of the sound. Dryer runs very quiet now.
GLTF2940FS Frigidaire Front Load Washer Stops Running
By · CommentsGLTF2940FS Frigidaire Front Load Washer
This washer is just over a year old. It started turning off in the middle of the load. The display would also go out. After waiting about 15-20 minutes you could start the washer again.
I had to replace the control board to repair this washer.
Manufacturer part number 137006000
DLE9577 New Drum, Rollers Too?
By · CommentsMission complete & Mama’s happy again – just stopped back to say, THANKS
I did not make clear, this was a DIY job
I did not spend the extra $80 and replace the rollers but did oil them & the tensioner – good tip
Based on all the lint build-up that was cleaned from the inside of the unit & vent, I set a clean schedule every 3 years. WOW, what a fire hazzard.
Thanks again, Boys
